Rebuild Kits

Master Rebuild Kit - Standard Duty SKF Bearings
Master rebuild kit with standard duty SKF bearings used to rebuild any 4 speed toploader. Available in any shaft size configuration. Kit contains: detent springs, all needle bearings, snap rings, thrust washers, spacers, speedometer ball, dowel pins, case plug, shift lever o-rings, front and rear seal, gasket set, C springs, new magnetic drain plug, counter shaft, 4 bronze original equipment blocker rings, front & rear main bearings, synchronizer keys, tailshaft bushing and instructions. This kit can be shipped next day air and second day air if necessary.

Master Rebuild Kit, 1-1/16" Input, 28 Spline Output $204.34 Master Rebuild Kit, 1-1/16" Input, 31 Spline Output $204.34 Master Rebuild Kit, 1-3/8" Input, 28 Spline Output $204.34 Master Rebuild Kit, 1-3/8" Input, 31 Spline Output $204.34
Road Race Rebuild Kit
Master rebuild kit with max duty SKF bearings used to rebuild all 4 speed toploaders. Available in any shaft size configuration. Kit contains: detent springs, all needle bearings, snap rings, thrust washers, spacers, speedometer ball, dowel pins, case plug, shift lever o-rings, front and rear seal, gasket set, C springs, new magnetic drain plug, counter shaft, 4 bronze original equipment blocker rings, front & rear main bearings, synchronizer keys, tailshaft bushing, air vent, 3 shift rail set screws and instructions. This kit can be shipped next day air and second day air if necessary.

Road Race Rebuild Kit, 1-1/16" Input, 28 Spline Output $240.33 Road Race Rebuild Kit, 1-1/16" Input, 31 Spline Output $240.33 Road Race Rebuild Kit, 1-3/8" Input, 28 Spline Output $240.33 Road Race Rebuild Kit, 1-3/8" Input, 31 Spline Output $240.33
Small Rebuild Kit
Available in any shaft size configuration. Kit contains: all needle bearings, snap rings, thrust washers, spacers, speedometer ball, dowel pins, case plug, shift lever o-rings, front and rear seal, gasket set and synchronizer C springs. (must specify shaft sizes)

Small Rebuild Kit, 1-1/16" Input, 28 Spline Output $87.75 Small Rebuild Kit, 1-1/16" Input, 31 Spline Output $87.75 Small Rebuild Kit, 1-3/8" Input, 28 Spline Output $87.75 Small Rebuild Kit, 1-3/8" Input, 31 Spline Output $87.75
Small Parts Kit$45.49DK296-SPK
Small parts kit includes: all needle bearings, snap rings, thrust washers, spacers, speedometer ball, dowel pins and detent springs.

Qty:
Seal and Gasket Kit
Contains: all gaskets, front and rear seal, three shift lever o-rings, rear bushing and case plug (must specify shaft sizes)

Seal and Gasket Kit, 1-1/16" Input, 28 Spline Output $44.38 Seal and Gasket Kit, 1-1/16" Input, 31 Spline Output $45.81 Seal and Gasket Kit, 1-3/8" Input, 28 Spline Output $52.19 Seal and Gasket Kit, 1-3/8" Input, 31 Spline Output $53.92
Top Cover$19.99DK296-30
Our new top cover is made with the same contour around the bolt holes as the originals. Replaces Ford part number C4AZ-7222-A. There is no air vent hole in this top cover. We recommend an air vent in the tailhousing (part number DK296-66) or you will have to drill a 3/32" hole in the center of the dimple like the original top cover.

Qty:
Air Vent$6.50DK296-66
With this air vent the hole in the top cover is no longer needed and can be blocked to stop oil from leaking out of it constantly. Use a letter R drill bit and 1/8” pipe thread tap to install the vent on the top of the tailhousing.

Qty:
Telescopic Magnet$6.50DK296-TM
Telescopic magnet used to remove and install detents and springs.
Plug (speedometer cable hole)$1.50SPPL
Plastic plug for speedometer cable hole in tailhousing. This plug will allow you to fill the transmission with gear lube before it is installed.

Qty:
28 Spline Plug$2.5028PL
Plastic plug for all 28 spline toploaders. This plug will allow you to fill the transmission with gear lube before it is installed.

Qty:
31 Spline Plug$2.5031PL
Plastic plug for all 31 spline toploaders. This plug will allow you to fill the transmission with gear lube before it is installed.

Qty: